FreeNASマニュアル/00準備
をテンプレートにして作成
[
トップ
] [
新規
|
一覧
|
単語検索
|
最終更新
|
ヘルプ
]
開始行:
#navi(FreeNASマニュアル)
#contents
*準備するもの [#f4bff980]
+パソコン
+CD-R/RW or DVD-R/RWなど
ここではそれぞれ
+FUJITSU FMV C6/865（たぶん）
+MITSUBISHI CD-RW700MB HIGHSPEED4x-16x
を用意。
*イメージ作成 [#j521d255]
+FreeNASのサイトからISOファイルをダウンロード。
+ライティングソフトで焼く。
*起動 [#d69fb655]
+BIOSの起動メニューを立ち上げる。通常F12とか。
+CD/DVDドライブから起動する。
*インストール [#s44a627a]
+→9) Install/Upgrade to hard drive/flash device, etc.
+→3) Install 'full' OS on HDD + DATA + SWAP partition
FreeNAS installation
FreeNAS 'full' installer for HDD.
-Create MBR partition 1, using UFS, customizable size fo...
-Create MBR partition 2, using UFS, for DATA
-Create MBR partition 3, as SWAP
-Easy to customize (e.g. install additional FreeBSD pack...
WARNING: There will be some limitations:
1. This will erase All partitions and data on the destin...
+→OK
Choose installation media
Select CD/DVD drive for installation.
acd0 TOSHIBA DVD-ROM SD-R1002/1746
+→OK
Choose destination media
Select media where FreeNAS OS should be installed.
ad0 38167MB <ST340823A/3.05>
+→OK
Enter the size for OS partition in MB (min 128MB):
容量入力。 5120(5GB)
+→OK
Do you want to add a swap partition?
+→yes
Enter the size of the swap partition in MB.
容量入力。 150(150MB)
+→OK
FreeNAS has been installed on ad0s1.
You can now remove the CDROM and reboot the PC.
To use the DATA partition:
- Add the disk ad0 on the 'Disks|Management' page.
- Add the mount point on the 'Disks|mount Point|Manageme...
Use the following parameters:
Disk ad0, Partition 2, Filesystem UFS
To use the SWAP partition:
- Enable swap space usage on the 'System:Advanced|Swap' ...
Use the following parameters:
Type: Device, Device: /dev/ad0s3
DO NOT format the drive ad0! The DATA partition has alre...
formated for you as part of the installation!
Press ENTER to continue.
+→Enter
+→7) Reboot System
Do you really want to reboot the system?
+→Yes
再起動。
*デバイス設定 [#m8a15150]
+→1) Assign interfaces
Configure LAN interface
If you don't know the names of your interfaces, you may ...
auto-detection. In that case, disconnect all interfaces ...
begin, and reconnect each one when prompted to do so.
rl0 00:0a:79:88:8b:a1 (up)
fwe0 02:20:ed:05:b4:aa
fwip0 00:20:ed:0b:00:05:b4:aa:0a:02:ff:fe:00:00:00:00
auto Auto-detection
+→auto Auto-detection
Connect the LAN interface now and make
sure that the link is up.
Press OK to continue.
+→OK
+→none Finish and exit configuration
The interfaces will be assigned as follows:
LAN -> rl0
Do you want to proceed?
+→Yes
*IP設定、確認 [#cdb5b027]
+→2) Set LAN IP address
Do you want to use DHCP for this interface?
+→Yes
Do you want to configuration IPv6 for this interface?
+→No
Initializing interface. Please wait...
The LAN IP address has been set to:
IPv4: 192.168.0.4
You can access the WebGUI using the following URL:
http://192.168.0.4:80
Press ENTER to continue.
+→Enter
*WebGUI 設定編 [#x3406209]
+ブラウザ起動
+IP設定、確認で出てきたhttp://～のURLにアクセスする。
Username admin
Password freenas
+初期設定でログインする。
#navi(FreeNASマニュアル)
終了行:
#navi(FreeNASマニュアル)
#contents
*準備するもの [#f4bff980]
+パソコン
+CD-R/RW or DVD-R/RWなど
ここではそれぞれ
+FUJITSU FMV C6/865（たぶん）
+MITSUBISHI CD-RW700MB HIGHSPEED4x-16x
を用意。
*イメージ作成 [#j521d255]
+FreeNASのサイトからISOファイルをダウンロード。
+ライティングソフトで焼く。
*起動 [#d69fb655]
+BIOSの起動メニューを立ち上げる。通常F12とか。
+CD/DVDドライブから起動する。
*インストール [#s44a627a]
+→9) Install/Upgrade to hard drive/flash device, etc.
+→3) Install 'full' OS on HDD + DATA + SWAP partition
FreeNAS installation
FreeNAS 'full' installer for HDD.
-Create MBR partition 1, using UFS, customizable size fo...
-Create MBR partition 2, using UFS, for DATA
-Create MBR partition 3, as SWAP
-Easy to customize (e.g. install additional FreeBSD pack...
WARNING: There will be some limitations:
1. This will erase All partitions and data on the destin...
+→OK
Choose installation media
Select CD/DVD drive for installation.
acd0 TOSHIBA DVD-ROM SD-R1002/1746
+→OK
Choose destination media
Select media where FreeNAS OS should be installed.
ad0 38167MB <ST340823A/3.05>
+→OK
Enter the size for OS partition in MB (min 128MB):
容量入力。 5120(5GB)
+→OK
Do you want to add a swap partition?
+→yes
Enter the size of the swap partition in MB.
容量入力。 150(150MB)
+→OK
FreeNAS has been installed on ad0s1.
You can now remove the CDROM and reboot the PC.
To use the DATA partition:
- Add the disk ad0 on the 'Disks|Management' page.
- Add the mount point on the 'Disks|mount Point|Manageme...
Use the following parameters:
Disk ad0, Partition 2, Filesystem UFS
To use the SWAP partition:
- Enable swap space usage on the 'System:Advanced|Swap' ...
Use the following parameters:
Type: Device, Device: /dev/ad0s3
DO NOT format the drive ad0! The DATA partition has alre...
formated for you as part of the installation!
Press ENTER to continue.
+→Enter
+→7) Reboot System
Do you really want to reboot the system?
+→Yes
再起動。
*デバイス設定 [#m8a15150]
+→1) Assign interfaces
Configure LAN interface
If you don't know the names of your interfaces, you may ...
auto-detection. In that case, disconnect all interfaces ...
begin, and reconnect each one when prompted to do so.
rl0 00:0a:79:88:8b:a1 (up)
fwe0 02:20:ed:05:b4:aa
fwip0 00:20:ed:0b:00:05:b4:aa:0a:02:ff:fe:00:00:00:00
auto Auto-detection
+→auto Auto-detection
Connect the LAN interface now and make
sure that the link is up.
Press OK to continue.
+→OK
+→none Finish and exit configuration
The interfaces will be assigned as follows:
LAN -> rl0
Do you want to proceed?
+→Yes
*IP設定、確認 [#cdb5b027]
+→2) Set LAN IP address
Do you want to use DHCP for this interface?
+→Yes
Do you want to configuration IPv6 for this interface?
+→No
Initializing interface. Please wait...
The LAN IP address has been set to:
IPv4: 192.168.0.4
You can access the WebGUI using the following URL:
http://192.168.0.4:80
Press ENTER to continue.
+→Enter
*WebGUI 設定編 [#x3406209]
+ブラウザ起動
+IP設定、確認で出てきたhttp://～のURLにアクセスする。
Username admin
Password freenas
+初期設定でログインする。
#navi(FreeNASマニュアル)
ページ名:
![[PukiWiki]](image/pukiwiki.png "[PukiWiki]")
