FreeNASマニュアル/00準備の編集

#navi(FreeNASマニュアル)
#contents
 
*準備するもの [#f4bff980]
+パソコン
+CD-R/RW or DVD-R/RWなど

ここではそれぞれ
+FUJITSU FMV C6/865（たぶん）
+MITSUBISHI CD-RW700MB HIGHSPEED4x-16x

を用意。

*イメージ作成 [#j521d255]
+FreeNASのサイトからISOファイルをダウンロード。
+ライティングソフトで焼く。

*起動 [#d69fb655]
+BIOSの起動メニューを立ち上げる。通常F12とか。
+CD/DVDドライブから起動する。

*インストール [#s44a627a]
+→9) Install/Upgrade to hard drive/flash device, etc.
+→3) Install 'full' OS on HDD + DATA + SWAP partition
 FreeNAS installation
 
 FreeNAS 'full' installer for HDD.
 -Create MBR partition 1, using UFS, customizable size for OS
 -Create MBR partition 2, using UFS, for DATA
 -Create MBR partition 3, as SWAP
 -Easy to customize (e.g. install additional FreeBSD packages)
 WARNING: There will be some limitations:
 1. This will erase All partitions and data on the destination disk
+→OK
 Choose installation media
 Select CD/DVD drive for installation.
 acd0 TOSHIBA DVD-ROM SD-R1002/1746
+→OK
 Choose destination media
 Select media where FreeNAS OS should be installed.
 ad0 38167MB <ST340823A/3.05>
+→OK
 Enter the size for OS partition in MB (min 128MB):
 容量入力。 5120(5GB)
+→OK
 Do you want to add a swap partition?
+→yes
 Enter the size of the swap partition in MB.
 容量入力。 150(150MB)
+→OK
 FreeNAS has been installed on ad0s1.
 You can now remove the CDROM and reboot the PC.
 To use the DATA partition:
 - Add the disk ad0 on the 'Disks|Management' page.
 - Add the mount point on the 'Disks|mount Point|Management' page.
   Use the following parameters:
   Disk ad0, Partition 2, Filesystem UFS
 To use the SWAP partition:
 - Enable swap space usage on the 'System:Advanced|Swap' page.
   Use the following parameters:
   Type: Device, Device: /dev/ad0s3
 DO NOT format the drive ad0! The DATA partition has already been
 formated for you as part of the installation!
 Press ENTER to continue.
+→Enter
+→7) Reboot System
 Do you really want to reboot the system?
+→Yes
再起動。

*デバイス設定 [#m8a15150]
+→1) Assign interfaces
 Configure LAN interface
 If you don't know the names of your interfaces, you may use
 auto-detection. In that case, disconnect all interfaces before you
 begin, and reconnect each one when prompted to do so.
 rl0 00:0a:79:88:8b:a1  (up)
 fwe0 02:20:ed:05:b4:aa
 fwip0 00:20:ed:0b:00:05:b4:aa:0a:02:ff:fe:00:00:00:00
 auto Auto-detection
+→auto Auto-detection
 Connect the LAN interface now and make
 sure that the link is up.
 Press OK to continue.
+→OK
+→none Finish and exit configuration
 The interfaces will be assigned as follows:
 LAN -> rl0
 Do you want to proceed?
+→Yes

*IP設定、確認 [#cdb5b027]
+→2) Set LAN IP address
 Do you want to use DHCP for this interface?
+→Yes
 Do you want to configuration IPv6 for this interface?
+→No
 Initializing interface. Please wait...
 The LAN IP address has been set to:
 IPv4: 192.168.0.4
 You can access the WebGUI using the following URL:
 http://192.168.0.4:80
 Press ENTER to continue.
+→Enter

*WebGUI 設定編 [#x3406209]
+ブラウザ起動
+IP設定、確認で出てきたhttp://～のURLにアクセスする。
 Username  admin
 Password  freenas
+初期設定でログインする。

#navi(FreeNASマニュアル)

タイムスタンプを変更しない