![[PukiWiki]](image/pukiwiki.png "[PukiWiki]")
#navi(FreeNASマニュアル) #contents *準備するもの [#f4bff980] +パソコン +CD-R/RW or DVD-R/RWなど ここではそれぞれ +FUJITSU FMV C6/865（たぶん） +MITSUBISHI CD-RW700MB HIGHSPEED4x-16x を用意。 *イメージ作成 [#j521d255] +FreeNASのサイトからISOファイルをダウンロード。 +ライティングソフトで焼く。 *起動 [#d69fb655] +BIOSの起動メニューを立ち上げる。通常F12とか。 +CD/DVDドライブから起動する。 *インストール [#s44a627a] +→9) Install/Upgrade to hard drive/flash device, etc. +→3) Install 'full' OS on HDD + DATA + SWAP partition FreeNAS installation FreeNAS 'full' installer for HDD. -Create MBR partition 1, using UFS, customizable size for OS -Create MBR partition 2, using UFS, for DATA -Create MBR partition 3, as SWAP -Easy to customize (e.g. install additional FreeBSD packages) WARNING: There will be some limitations: 1. This will erase All partitions and data on the destination disk +→OK Choose installation media Select CD/DVD drive for installation. acd0 TOSHIBA DVD-ROM SD-R1002/1746 +→OK Choose destination media Select media where FreeNAS OS should be installed. ad0 38167MB <ST340823A/3.05> +→OK Enter the size for OS partition in MB (min 128MB): 容量入力。 5120(5GB) +→OK Do you want to add a swap partition? +→yes Enter the size of the swap partition in MB. 容量入力。 150(150MB) +→OK FreeNAS has been installed on ad0s1. You can now remove the CDROM and reboot the PC. To use the DATA partition: - Add the disk ad0 on the 'Disks|Management' page. - Add the mount point on the 'Disks|mount Point|Management' page. Use the following parameters: Disk ad0, Partition 2, Filesystem UFS To use the SWAP partition: - Enable swap space usage on the 'System:Advanced|Swap' page. Use the following parameters: Type: Device, Device: /dev/ad0s3 DO NOT format the drive ad0! The DATA partition has already been formated for you as part of the installation! Press ENTER to continue. +→Enter +→7) Reboot System Do you really want to reboot the system? +→Yes 再起動。 *デバイス設定 [#m8a15150] +→1) Assign interfaces Configure LAN interface If you don't know the names of your interfaces, you may use auto-detection. In that case, disconnect all interfaces before you begin, and reconnect each one when prompted to do so. rl0 00:0a:79:88:8b:a1 (up) fwe0 02:20:ed:05:b4:aa fwip0 00:20:ed:0b:00:05:b4:aa:0a:02:ff:fe:00:00:00:00 auto Auto-detection +→auto Auto-detection Connect the LAN interface now and make sure that the link is up. Press OK to continue. +→OK +→none Finish and exit configuration The interfaces will be assigned as follows: LAN -> rl0 Do you want to proceed? +→Yes *IP設定、確認 [#cdb5b027] +→2) Set LAN IP address Do you want to use DHCP for this interface? +→Yes Do you want to configuration IPv6 for this interface? +→No Initializing interface. Please wait... The LAN IP address has been set to: IPv4: 192.168.0.4 You can access the WebGUI using the following URL: http://192.168.0.4:80 Press ENTER to continue. +→Enter *WebGUI 設定編 [#x3406209] +ブラウザ起動 +IP設定、確認で出てきたhttp://～のURLにアクセスする。 Username admin Password freenas +初期設定でログインする。 #navi(FreeNASマニュアル) // IP:"126.60.107.119" TIME:"2014-03-24(<abbr class="week_day" title="月曜日">月</abbr>)23:48:11" REFERER:"http://157.7.130.26/" USER_AGENT:"Mozilla/5.0 (Windows NT 6.3; WOW64) AppleWebKit/537.36 (KHTML, like Gecko) Chrome/33.0.1750.146 Safari/537.36
